You may have a sunken concrete slab that requires leveling. Fortunately, it can be fixed quickly and at a fraction of the cost of a replacement. For professional help, contact Concrete Contractors Dallas TX.
A-1 Concrete Leveling uses a patented, environmentally friendly limestone slurry grout leveling process to raise sunken concrete. The limestone slurry mixture is hydraulically pumped under the slab to fill voids and lift the slab back up.
Concrete slabs often become unlevel due to soil erosion or water corrosion. This creates tripping hazards for pedestrians and can result in costly property damage. Fortunately, you can level sunken concrete using a cost-effective method that does not require replacing the entire slab. Slabjacking, also known as mudjacking, involves drilling holes into the concrete and pumping a cement-like mixture to raise the concrete back up to its original level.
A trained specialist can perform the process in a few hours, compared to the days required for traditional concrete replacement. The holes are much smaller—less than 1 inch in diameter—and the material used weighs considerably less than a typical mudjacking mixture. This means that the injected mixture does not place too much pressure on the soft ground underneath the slab and will not cause further sinking of the concrete.
When you hire a qualified technician for the job, the specialist will first drill the necessary holes. Then, the specialized material is pumped into these holes via a long hose. The material is pumped at a rate of about one inch per minute, which allows it to fill the void under the slab and slowly lift the concrete.
Once the slab is raised to its proper level, the holes are patched with a thin layer of material. This material is hard to tell from the surrounding concrete once it has been finished. As a result, the repair is minimally invasive to your home or business and requires very little downtime.
Although the procedure is safe for most areas, it’s important to hire a professional for the project. This is because the mix used for the injection needs to have a specific consistency to lift the concrete properly. A good contractor will use a mix of Portland cement, fly ash, limestone dust, and other materials to achieve this.
In addition to the concrete slab, this method can also be used to repair sagging garage floors, basement floors, pool decks, driveways, sidewalks, and other areas. The best part about the process is that it’s cheaper and more efficient than pouring a new slab of concrete, which can be expensive, time-consuming, and messy.
Mudjacking
Mudjacking is a common solution for raising and leveling concrete slabs that have sunken. The technique involves drilling a series of holes into the slab and pumping a mixture of water, sandy loam soil, and cement into them. The mixture is then pumped through the hole into the sunken slab, and pressure lifts it up into its original position. This concrete repair method can also be used to stabilize a slab that has voids but has not actually sunk into the ground.
The mudjacking process is less disruptive than a full replacement and is typically completed in hours. It is a more eco-conscious choice since you are restoring the existing concrete rather than throwing it out and starting over. It is also less expensive than a full replacement, which can run upwards of $4,000.
When you choose to use the mudjacking technique, there are some things you need to keep in mind. First, mudjacking does not eliminate cracks in the concrete surface; it only brings them together and removes tripping hazards. It is not a good solution for concrete surfaces that have been covered with tile or other cosmetic top treatments. It is also not a permanent solution and can sink back into its old position.
Unlike polyurethane foam jacking, mudjacking can shift and is not water-resistant. The slurry mix can leak into your foundation and cause damage to the structure below. It is also not an ideal solution if you have a concrete slab that has settled due to poor soil conditions underneath.
When you have a problem with your concrete foundation that needs to be raised, it is important that you consult a professional. They can help you decide which method is best for your situation and provide a cost estimate for the work. Contact Anchor Foundation Repair for more information about mudjacking or to get a quote for your project!
Foam Leveling
Uneven concrete can be unsightly to look at and dangerous for pedestrians and vehicles. It’s also costly to repair and can contribute to structural issues throughout your home or building. Fortunately, there is an alternative to replacing sunken concrete slabs. Concrete leveling is a cost-effective and efficient solution for lifting uneven concrete surfaces. This method uses polyurethane foam to fill voids and lift concrete, resulting in a more even surface that will last longer than other methods.
Concrete leveling can be used to address uneven sidewalks, patios, driveways, and the concrete around a swimming pool or in commercial buildings. It can also be used to repair concrete slabs that have settled or are sloping in one direction. This method is quick and requires minimal disturbance to the surrounding area. Concrete leveling can be completed in a matter of hours for residential jobs and several days for larger commercial projects.
The process of concrete leveling starts with drilling holes in the concrete that is sinking or sloping. These holes are then filled with a mixture of cement, grout slurry, or concrete lifting foam. The mixture is pumped into the holes, closing any gaps or voids in the soil underneath the concrete. The polyurethane foam expands to lift the concrete. Once the concrete is lifted, the holes are patched up, and the process is complete.
Another way to raise concrete is by using mud or a cement-slurry mixture. Mudjacking dates back to the 1930s and involves pumping mud or other natural materials under the concrete to lift it up. The problem is that the heavy mud can actually cause the concrete to sink again when it is exposed to water.
The most modern concrete leveling technique is to use polyurethane foam to lift the concrete. Holes are drilled in the concrete, and the foam is injected into those holes to create a chemical reaction under the surface that expands the concrete. This method is more economical than mudjacking, and it also doesn’t cause the concrete to sink again. It’s a much better option for homeowners, businesses, and municipalities that are trying to save money while maintaining safe and secure properties.
Stone Slurry Leveling
Concrete leveling is the process of correcting uneven or sinking concrete slabs by altering the foundation that the surface sits on. This is typically less expensive than replacing the entire concrete surface. It is often used to help with problems like sagging garage floors, sunken basements, and concrete sidewalks. Concrete leveling can be performed in residential, commercial, and industrial applications. Homes, warehouses, roads, shopping centers, and airports can all benefit from this type of repair.
The concrete leveling method you choose will depend on the cause of your sinking concrete and the size of the area that needs to be repaired. The different methods available include foam leveling, mud jacking, and stone slurry leveling. While they all work in similar ways, each has its own advantages and disadvantages.
Mudjacking is a similar concrete leveling method to slurry cement, but it uses a different leveling mixture and requires larger holes to be drilled. The mudjacking mixture includes soil, sand, and water that is injected under the concrete through holes drilled in the slab. The concrete is then lifted by the mudjacking slurry. The pressure that is pumped with the mudjacking method is much higher than for the other concrete leveling methods. This can cause damage to the concrete if too much is lifted, and it is harder to control.
For this reason, mudjacking is not recommended for slabs that are in very poor condition. Stone slurry leveling, on the other hand, is more forgiving and can be used on older and newer concrete surfaces. Holes are drilled into the concrete, and then a mixture of agricultural limestone and water is pumped under the slab. This fills the void beneath the slab and lifts it. The limestone mixture is then topped with a layer of non-shrink grout, which is placed over the surface.
Unlike the other concrete leveling options, limestone slurry leveling doesn’t require any chemical additives. It is also environmentally friendly. The limestone powder used in this process is harvested from local quarries near each A-1 location, supporting the economy of each community. This also helps to ensure that the concrete leveling is as durable and long-lasting as possible.